Scooter Hoverboard Motherboard Part 2 Wheels Self Balancing Electric Scooter Parts

Scooter Hoverboard Part 2 Wheels Self Balancing Electric Scooter Replacement Universal for 6.5/8/10 Inches Hoverboard Parts(9in1)

hoverboard motherboard

 Attention:              

- This buy link is for wholesale 1 Motherboard, 2 Gyroscope boards, 2 Front LED lights boards, 2 Power Indicator boards, 1 Charger line and 1 Power cord,9 iterms in all.

NOT including a bluetooth board.

 

 Tips:                           

Controllers learning Calibration: off, long press the power button for 5 seconds, "drip" sound until around headlights flash, attitude data successfully saved, to be re-switch. (In the calibration, be sure to keep the left and right pedals parallel to the ground.)

Mode Switching: power-on default low sensitivity mode (beginner mode), the off state, press the power button, and within seconds the power button is pressed again, issued a drip sound mode is switched to the high-sensitivity mode (Motion mode). Reboot back to learning mode.

Tilt protection: stepping on the pedal, the pedal must be less than the level of 10 degrees beyond the angle, the motor stops, status indication red. Power indicator board each 6 LED. Cool side panel of each lamp 8 LED.

Uses: Suitable for assembling 2 wheel electric self balancing boards.

 

 Package including:             

- 1 Motherboard, 2 Gyroscope boards, 2 Front LED lights boards, 2 Power Indicator boards, 1 Charger line and 1 Power cord

- Packing size: 16 x 12 x 10 cm

DIY-Scooter-Parts-6-5-8-10-Electric-Scooter-Mainboard-Hoverboard-Motherboard-Circuit-Control-Board-PCB

 

 

61FkBrP0WKL__SL1000_

 

DIY-Scooter-Parts-6-5-8-10-Electric-Scooter-Mainboard-Hoverboard-Motherboard-Circuit-Control-Board-PCB (3)

 

HTB1zvHHQVXXXXanaXXXq6xXFXXXa (1)

 TaoTao-PCB-Repair-for-6-5-8-10-inch-2-Wheels-Self-Balancing-Scooter-TaoTao-Motherboard (1)

 

Certification

 

certification of motherboard

 

 

Portable 2 Wheel Self Balancing e-scooter Hoverboard Bag/Pouch Scooter Parts & Accessories 6"/8"10" Balance Scooter

9 in 1 Motherboard

 Attention:              

 

We have US warehouse,the delivery time is about 5-7 working days.

- This buy link is for wholesale 1 Motherboard, 2 Gyroscope boards, 2 Front LED lights boards, 2 Power Indicator boards, 1 Charger line and 1 Power cord,9 iterms in all.

NOT including a bluetooth board.

 

 Tips:                           

 

Controllers learning Calibration: off, long press the power button for 5 seconds, "drip" sound until around headlights flash, attitude data successfully saved, to be re-switch. (In the calibration, be sure to keep the left and right pedals parallel to the ground.)

Mode Switching: power-on default low sensitivity mode (beginner mode), the off state, press the power button, and within seconds the power button is pressed again, issued a drip sound mode is switched to the high-sensitivity mode (Motion mode). Reboot back to learning mode.

Tilt protection: stepping on the pedal, the pedal must be less than the level of 10 degrees beyond the angle, the motor stops, status indication red. Power indicator board each 6 LED. Cool side panel of each lamp 8 LED.

Uses: Suitable for assembling 2 wheel electric self balancing boards.

 

 Package including:             

- 1 Motherboard, 2 Gyroscope boards, 2 Front LED lights boards, 2 Power Indicator boards, 1 Charger line and 1 Power cord

- Packing size: 16 x 12 x 10 cm

DIY-Scooter-Parts-6-5-8-10-Electric-Scooter-Mainboard-Hoverboard-Motherboard-Circuit-Control-Board-PCB

 

 

61FkBrP0WKL__SL1000_

 

DIY-Scooter-Parts-6-5-8-10-Electric-Scooter-Mainboard-Hoverboard-Motherboard-Circuit-Control-Board-PCB (3)

 

HTB1zvHHQVXXXXanaXXXq6xXFXXXa (1)

 

TaoTao-PCB-Repair-for-6-5-8-10-inch-2-Wheels-Self-Balancing-Scooter-TaoTao-Motherboard (1)

 Tips for repairing your scooter:

234766-131230091G7111

This post may help for all kind of (hover board) electric scooter fault diagnosis.

most of the faulty issues are because of some cables inside are loose or disconnect.

It usually caused from the shaking when shipping or riding or carelessness of our factory.

it will be easy to fix by yourself instead of wasting too much time for replacement.

B1

the scooter has 3 circuit boards, one big main board and 2 co-board.

B2

B3

B4

B5

B6

B7

B8

 

 

Certification

 

certification of motherboard

 

 

 

Wholesale 1 set Scooter Control Board for Hoverboard/Electric 2 Wheel Scooter

 

Taotao motherboard

 Attention:              

 

We have US warehouse,the delivery time is about 5-7 working days.

- This buy link is for wholesale 1 Motherboard, 2 Gyroscope boards, 2 Front LED lights boards, 2 Power Indicator boards, 1 Charger line and 1 Power cord,9 iterms in all.

NOT including a bluetooth board.

 

 Tips:                           

 

Controllers learning Calibration: off, long press the power button for 5 seconds, "drip" sound until around headlights flash, attitude data successfully saved, to be re-switch. (In the calibration, be sure to keep the left and right pedals parallel to the ground.)

Mode Switching: power-on default low sensitivity mode (beginner mode), the off state, press the power button, and within seconds the power button is pressed again, issued a drip sound mode is switched to the high-sensitivity mode (Motion mode). Reboot back to learning mode.

Tilt protection: stepping on the pedal, the pedal must be less than the level of 10 degrees beyond the angle, the motor stops, status indication red. Power indicator board each 6 LED. Cool side panel of each lamp 8 LED.

Uses: Suitable for assembling 2 wheel electric self balancing boards.

 

 Package including:             

- 1 Motherboard, 2 Gyroscope boards, 2 Front LED lights boards, 2 Power Indicator boards, 1 Charger line and 1 Power cord

- Packing size: 16 x 12 x 10 cm

DIY-Scooter-Parts-6-5-8-10-Electric-Scooter-Mainboard-Hoverboard-Motherboard-Circuit-Control-Board-PCB

 

 

61FkBrP0WKL__SL1000_

 

DIY-Scooter-Parts-6-5-8-10-Electric-Scooter-Mainboard-Hoverboard-Motherboard-Circuit-Control-Board-PCB (3)

 

HTB1zvHHQVXXXXanaXXXq6xXFXXXa (1)

 

TaoTao-PCB-Repair-for-6-5-8-10-inch-2-Wheels-Self-Balancing-Scooter-TaoTao-Motherboard (1)

 Tips for repairing your scooter:

234766-131230091G7111

This post may help for all kind of (hover board) electric scooter fault diagnosis.

most of the faulty issues are because of some cables inside are loose or disconnect.

It usually caused from the shaking when shipping or riding or carelessness of our factory.

it will be easy to fix by yourself instead of wasting too much time for replacement.

B1

the scooter has 3 circuit boards, one big main board and 2 co-board.

B2

B3

B4

B5

B6

B7

B8

 

 

Certification

 

certification of motherboard

 

 

hoverboard parts (motherbord)

Related Items